Blog‎ > ‎

Category 6 UTP connectors patch cable patch panels installation Los Angeles Orange county

posted Jan 31, 2013, 8:27 AM by David Khorram   [ updated by Virtual Augmented Reality ]
Installation instructions for Giganet Category 6 UTP connectors and patch panels used in a structured cabling system. 



Category 6 cable, commonly referred to as Cat 6, is a standardized cable for Gigabit Ethernet and other network physical layers that is backward compatible with the Category 5/5e and Category 3 cable standards.[citation needed] Compared with Cat 5 and Cat 5e, Cat 6 features more stringent specifications for crosstalk and system noise.[citation needed] The cable standard provides performance of up to 250 MHz and is suitable for 10BASE-T100BASE-TX (Fast Ethernet), 1000BASE-T/1000BASE-TX (Gigabit Ethernet) and 10GBASE-T (10-Gigabit Ethernet).[citation needed]

Whereas Category 6 cable has a reduced maximum length when used for 10GBASE-T; Category 6a cable, or Augmented Category 6, is characterized to 500 MHz and has improved alien crosstalk characteristics, allowing 10GBASE-T to be run for the same distance as previous 


Category 6

Like most earlier twisted-pair cable, Category 6 cable contains four twisted wire pairs. Attenuation, near end crosstalk (NEXT), and PSNEXT (power sum NEXT) in Cat 6 cable and connectors are all significantly lower than Cat 5 or Cat 5e, which uses 24 AWG wire.[citation needed] The increase in performance with Cat 6 comes mainly from increased (22 AWG) wire size.[note 1][citation needed]

The heavier wire in some Cat 6 cables makes them too thick to attach to standard 8P8C connectors without a special modular piece, resulting in a technically out-of-compliance assembly.[citation needed] Because the conductor sizes are generally the same, Cat 6 jacks may also be used with Cat 5e cable.[citation needed]

Category 6 cable can be identified by the printing on the side of the cable sheath.[1]

Cat 6 patch cables are normally terminated in 8P8C modular connectors. If Cat 6 rated patch cables, jacks, and connectors are not used with Cat 6 wiring, overall performance is degraded to that of the cable or connector.[citation needed]

Connectors use either T568A or T568B pin assignments; although performance is comparable provided both ends of a cable are the same, T568A is a deprecated standard in the US and no longer supported by TIA. The pin out for T568A should still be noted because when a crossover cable is used, one end is terminated T568B, and the other is T568A.

PinT568A PairT568B PairWireT568A ColorT568B ColorPins on plug face (socket is reversed)
132tipPair 3 Tip
white/green stripe
Pair 2 Tip
white/orange stripe
Rj45plug-8p8c.png
232ringPair 3 Ring
green solid
Pair 2 Ring
orange solid
323tipPair 2 Tip
white/orange stripe
Pair 3 Tip
white/green stripe
411ringPair 1 Ring
blue solid
Pair 1 Ring
blue solid
511tipPair 1 Tip
white/blue stripe
Pair 1 Tip
white/blue stripe
623ringPair 2 Ring
orange solid
Pair 3 Ring
green solid
744tipPair 4 Tip
white/brown stripe
Pair 4 Tip
white/brown stripe
844ringPair 4 Ring
brown solid
Pair 4 Ring
brown solid

Note: This is from left to right, with the plastic latching tab facing away from the viewer.


Category 6a

The latest standard from the TIA for enhanced performance standards for twisted pair cable systems was defined in February 2008 in ANSI/TIA/EIA-568-B.2-10. Category 6a (or Augmented Category 6) is defined at frequencies up to 500 MHz—twice that of Cat. 6.

Category 6a performs at improved specifications, in particular in the area of alien crosstalk as compared to Cat 6 UTP (unshielded twisted pair), which exhibited high alien noise in high frequencies.

The global cabling standard ISO/IEC 11801 has been extended by the addition of amendment 2. This amendment defines new specifications for Cat. 6A components and Class EA permanent links. These new global Cat. 6A/Class EA specifications require a new generation of connecting hardware offering far superior performance compared to the existing products that are based on the American TIA standard.[2]

The most important point is a performance difference between ISO/IEC and EIA/TIA component specifications for the NEXT transmission parameter. At a frequency of 500 MHz, an ISO/IEC Cat. 6A connector performs 3 dB better than a Cat. 6A connector that conforms with the EIA/TIA specification. 3 dB equals 100% increase of near-end crosstalk noise reduction when measured in absolute magnitudes; see 3dB-point.[2]

Confusion therefore arises because of the different naming conventions and performance benchmarks laid down by the International ISO/IEC and American TIA/EIA standards, which in turn are different from the regional European standard, EN 50173-1. In broad terms, the ISO standard for Cat6A is the highest, followed by the European standard and then the American.[3][4]


Maximum length

When used for 10/100/1000BASE-T, the maximum allowed length of a Cat 6 cable is 100 meters or 328 feet. This consists of 90 meters (300 ft) of solid "horizontal" cabling between the patch panel and the wall jack, plus 10 meters (33 ft) of stranded patch cable between each jack and the attached device. Since stranded cable has higher attenuation than solid cable, exceeding 10 metres of patch cabling will reduce the permissible length of horizontal cable.

When used for 10GBASE-T, Cat 6 cable's maximum length is 55 meters (180 ft) in a favourable alien crosstalk environment, but only 37 meters (121 ft) in a hostile alien crosstalk environment, such as when many cables are bundled together. However, because the effects of alien crosstalk environments on cables are difficult to determine prior to installation, it is highly recommended that all Cat6 cables being used for 10GBASE-T are electrically tested once installed. With its improved specifications, Cat6A does not have this limitation and can run 10GBASE-T at 100 meters (330 ft) without electronic testing.


Installation caveats

Category 6 and 6a cable must be properly installed and terminated to meet specifications. The cable must not be kinked or bent too tightly (the bend radius should be at least four times the outer diameter of the cable[5]). The wire pairs must not be untwisted and the outer jacket must not be stripped back more than 1/2 inch (1.27 cm).

All shielded cables must be grounded for safety and effectiveness and a continuous shield connection maintained from end to end.[6] Ground loops develop when there is more than one ground connection and the difference in common mode voltage potential at these ground connections introduces noise into the cabling.[7]


Notes

  1. ^ 23 or 24 AWG wire is allowed if the ANSI/TIA-568-B.2-1 performance specifications are met.


See also


References

  1. ^ Ethernet Cable Identification and Use [dead link]
  2. a b "A new Category 6A specification has arrived"Next generation Cat. 6A. Tyco Electronics. Retrieved 2011-03-22.
  3. ^ "Cat. 6A ≠ Cat. 6 A ≠ Class EA"Next generation Cat. 6A. Tyco Electronics. Retrieved 2011-03-22.
  4. ^ Cabling: The Complete Guide to Network Wiring, 3rd Edition
  5. ^ "Category 5 / 5E & Cat 6 Cabling Tutorial and FAQ's". LANshack.com. Retrieved 2012-01-06.
  6. ^ Barry J. Elliott (2002). Designing a structured cabling system to ISO 11801. Woodhead. p. 131. ISBN 978-1-85573-612-2.
  7. ^ "Screened and Shielded Cabling - Noise Immunity, Grounding, and the Antenna Myth". Siemon. Retrieved 2011-02-15.


External links

Comments